The grout is dug out from around the tile with a utility knife first to help. This is standard 12 floor tile thinsetted to (what looks like) hardibacker board on top of a 3/4 subfloor.

Infloor Scissor Lift Install Page 45 The Garage

To do that, put a straightedge across one of the diagonals.

How to remove tile floor and cement board. Remove as much of the grout as possible using a powered grout removal tool like a handheld oscillating tool with a grout removal blade, but do not spend an excessive amount of time on this step. The sledgehammer is only for breaking up the tile, not for removing everything. If you have this type of water damage, you need to remove the board as well as any rotted substrate material and replace them with new.

Saw slowly just until you break through the cement backer board. There’s nothing subtle about breaking through tile. Once you have removed the first tile, examine the substrate of the floor to decide on the best course of action in removing the rest of the tiles as there are concrete floors, timber floors, or timber floors that have cement sheeting (tile board underlay) laid over the top of the timber floor.

Take the flat garden spade and drive it between the wood subfloor and the cement board. Apply the product to the glue. How to remove tile floor

These are 1 inch thick boards that go over your floor joists because plywood was not used back then. Remember to offset the joints between the cement board and the subfloor and to gap the cement board sheets by 1/4 inch. Here is an idea to consider.

Start by scoring the old tile. While there is likely a structural problem due to inadequate subfloor and possibly failure to apply thinset under the cement board, it is very likely that the thinset used to apply the tiles was not mixed properly or was very old because the tiles you removed should have a hard coating of thinset on the backside and from what you described there was a total failure to adhere to the tiles. Try to get about 6 inches of the spade under the cement board.

Choose a tile in the center of the room and break up by hitting it in the center with a hammer. Removing ceramic tile with a garden spade. Here’s how to remove stubborn tile from a wall or floor:

Strike the punch with the mallet to break the tile into pieces. Mix fresh mortar only as it's needed to prevent it from drying before you can use it up. Removing floor tiles laid on cement board is more work than wall tiles but the methodology is similar.

Start near the center of the wall or floor. Repeat on the other diagonal. Just pick a few in the middle of the floor and whack away until you can see what’s underneath.

Keep in mind, there are warnings for using tile adhesive. Broken shards of tile can slice skin like a knife. I need advice on how to best remove two types of flooring.

Remove the broken piece of tile from the hardie board. Pry up enough to get a grasp on it with both hands. Plywood is best but most likely you have an older home with floor boards.

Pull the backer board up and off the floor. Whats people lookup in this blog: In order to remove dried cement from tile, wood, glass and other surfaces, there are many commercial products available that safely do the job.

The concrete floor is unlike those on cement board or wood since no underlayment or subfloor can be pried up and thrown away as you would undress. To remove tile yourself, put on some safety glasses and leather work gloves; If you have a single or a few cracked tiles, they can be removed from the cement backerboard and replaced.

This will force the sharp edge of the chisel under the mortar and free the shard. Professionals also recommend vinegar if cleaning dried concrete from hands after working with fresh cement. First remove one or a few tiles in the center of the room and dig down to see what is under the mortar.

How to remove ceramic floor tile from cement board You will feel them under your feet as you walk, or you will hear them and see the floor move under your weight. Now, you may be able to remove a starter tile using your putty knife, but more likely, you will need to remove the grout around a few.

I've laid plenty of tile but not demolition. Choose an edge, where flooring and the wall come together, and start by removing any edgings or moldings. Removing tile from concrete will require you to use your strength to the fullest because you have to knock the tiles out instead of them coming out without any real force.

You can't get a better garden spade. Loose sections walk across the backer board surface to determine if there are any loose sections on the floor; How to remove tile and backer board from the floor or wall you tile and cement board removal you how to remove tile and backer board from your floor you how to remove tile and cement backer board the easy way fast.

Insert the tip of a pry bar into any crack or seam under the backer board. Guide a scoring tool along the straightedge, scratching a line in the tile. Lift up on the handle to lift the cement board.

If the tile comes off the cement board fairly easy, you could leave the cement board, scrape off the thinset and lay your foam and laminate over the cement board. Place a point punch in the middle of the tile. Don’t confuse that with hardwood floors.

Continue installing sheets to cover the entire floor area. Make sure to allow the solvent at least an hour before trying to scrape away the adhesive, or whatever else is left. Often, the tool is useful for dislodging the flooring material from the adhesive.

Just a thought depending on the overall thickness you need to achieve.